Tag Archives: how to hoop

Learn to hoop towels the easy way!

#omlembroidery #machineembroidery #embroidery

In this video, I am going to show you how to hoop a fluffy bath towel with little or no hoop burn. You can use your embroidery hoop properly for towels! Yes, it can be done! If you do get some hoop burn, I will show you how to get rid of the hoop burn quickly and completely. Hooping a towel: there are a few things to do. If you have a hooping workout, you are not doing it properly and you are causing the hoop burn! Yes, it is true, you are. Hoop burn is caused by the compression and subsequent “dehydration” of the fabric that is compressed and squished between the two parts. When the hoop is too tight and you have to push, you are further compressing the towel fabric. The solution is to make your hoop fit the towel better by making sure that the hoop is loose enough so that it goes into the right place with only a little bit of pressure. Once you take your towel to the embroidery machine and stitch out your design, remove the hoops and fluff up the towel fabric. That’s pretty much it! In this video, I hooped the towel with a 4×4 hoop from my multi-needle embroidery machine as well as the small hoop from my Brother Dream Machine 2 (McDreamy) (both brother embroidery machines, a multi-needle and a single needle embroidery machine) to show you that hooping a towel can be done with any embroidery machine hoops. Using this technique, you will be able to hoop any type of fabric and create any type of embroidery design. You can do applique on a towel, or an in the hoop embroidery design (just skip the last step) so anything goes. Pro TIP: for a large embroidered towel like the one I am using, make sure you have your support table on your brother Multi needle machine. If you are using a Brother Dream Machine 2, make sure that you have the embroidery design and hoop rotated so that the bulk of the towel is not going to get caught up on the embroidery machine arm and doesn’t get too heavy for the embroidery arm to move properly. Plan it out so the towel stitches out smoothly.

MACHINE EMBROIDERY EDUCATION. FOR EVERYONE.

LEARN. STITCH. SMILE.

Happy stitching!

Sue Brown 🙂

6 Common Machine Embroidery HOOPING Mistakes

The 6 Common Embroidery Hooping Mistakes that change the outcome of your embroidery work. True Story. Read on, fellow embroiderers.

Hooping Skills:  the most important skill to learn in embroidery.

I have said it before, and I will keep saying it:  YOU ARE ONLY AS GOOD AS YOUR HOOPING SKILLS.

I know, I know.  I am such a nag, right?  Nah, not really.  I just want to get everyone to see that there is in fact, a right way and a wrong way when you are hooping.  How do I know this?  Years and years of experience, thousands of embroidery designs stitched on just about every fabric/item you can think of,  more learning, and tons of time figuring it all out.  So why not take advantage of what I know, and then you know how to do it right?  Why not set yourself apart from everyone else who does embroidery? You can do better, I just know it.

You are only as good as your hooping skills:  It makes sense, doesn’t it?  You can have the most beautiful embroidery design on the screen, and when you stitch it out, it looks terrible.  Why?  Hooping skills, that’s why!  If you don’t hoop something properly, it is not going to stitch properly.  If you don’t use the right size hoop, you may have mistakes.  If you don’t use the right kind of stabilizer, you will have issues.  Everything comes back to proper hooping skills.

Learn them, and learn them well.

Here are the 6 biggest mistakes in embroidery today.

  1. Using the wrong sized hoop for the job:

I see this time and time again – using the wrong sized hoop!  If you have a small design, you do not want to use a 5×7 hoop for that design – you want the smallest hoop that will fit your design.  You can figure this out in your software, or even on some machines.  My small single needle machine has some icons that tell you what sized hoop that you should be using.  Actually, it doesn’t tell you the right size, it shows you the size that your design will fit on.  It shows you the smallest size to the biggest size that is available.  Yes, the machine will stitch a 2×3 design on a 6×10 hoop, but that is not what you should be doing.   The smallest sized hoop for the design will ensure the proper stabilization and tension of the fabric and stabilizer when you hoop – and it will be easier to maintain that support when the design is embroidering.  If you use a bigger hoop, there is a bigger chance that the material will slip during embroidery.  Even if it slips a tiny bit, 1mm, that means that the part of your design that is stitching will be 1mm out.  Ok, that might not be too much, but it is quite possible that it may happen a few times- and then you will be out of registration on your design.  And that looks bad.

  • Floating stabilizer instead of hooping it.

I am pretty sure we have gone over this one before.  Let’s all say it together. Ready?  Float a boat, not stabilizer.  Or fabric.  Or anything.  Floating is for boats, not embroidery.   If you want sub-par or OK, results, keep floating.  If you want professional level, better-than-OK embroidery that you can be proud of, learn how to hoop properly.

  • Not hooping the fabric or garment:

See above.  Say it all over again, one more time.  You need to hoop stabilizer AND fabric at the same time.  Basting and (gasp) pins are NOT the same thing as hooping.  Basting stitches may generally hold your fabric in place, but it is not hooped and does not have the same consistent final results.   You may think it is good enough, but in reality, it just isn’t.  There is nothing that can take the place of hooping.  So hoop everything, please.

This embroidery design is using the proper hoop size for the large design, the felt and stabilizer are hooped properly.

  • Pulling the fabric:

Yes, this is a big mistake when you are hooping, I see it all the time – and yes, I can tell from a picture that it was not hooped properly, and sometimes I can even tell the mistake.  And this is one of them!  When you are hooping properly, you take the material and the stabilizer and put the hoop together kind of tightly, and when you have everything just so you make the hoop tight so that it will hold everything together. Before you tighten the hoop, you can make some small adjustments, depending on the type of material that you are using and gently pull the fabric into place. What if the material isn’t quite in the right place?  What do you do?  Some people think it is ok to pull on the fabric (and stretch it)  to get it into the right position.  While it may be ok to flatten or pull slightly before you tighten the hoop, anything more than that will cause you so many issues!  Think about it, when you pull the fabric that is already hooped, you are basically stretching the fabric.  When you are finished embroidering, and remove the hoop, what is going to happen?  The fabric does not have anything holding it in the stretched position, so it is going to go back to its normal position, and that will cause some nasty puckering.  It is better to hoop again until you get it right, without stretching the fabric.  Keep hooping it until you get it right.  There really is no point embroidering anything if it doesn’t look great when you are done, right?  RIGHT?  Take your time, hoop properly and carefully.

  • Not hooping fabric because you are worried about Hoop burn:

Hoop burn is no excuse for not hooping something properly. Yes, hoop burn happens!  It really is not a big deal, and is easily fixed, and hoop burn will happen less and less the better you are at your hooping skills.  We have also talked about this one, all you need is a little bit of steam.  If you have hoop burn, have some tea – but before you make the tea, use a little bit of steam on your item to solve that hoop burn.  It is literally fixed in 5 minutes.  So don’t let hoop burn ruin your embroidery, learn to hoop properly and fix it quickly with a little bit of steam if you need to.

  • Not using the right stabilizer:

You need to use the right stabilizer for the embroidery and for the fabric that you are using.  Hatch takes the guesswork out of what stabilizer you should use for certain embroidery.  There are many types of stabilizer, but they fall into two categories:  cutaway and tearaway.    Cutaway offers more stability – it is thicker and more stable and you must use scissors to cut it away.  Tearaway is exactly how it sounds- you can tear it away instead of cutting it.  Obviously tear away is much thinner and less stable than cutaway.  There are also fusible stabilizers, water-soluble stabilizers, no show mesh stabilizers, and the list goes on and on.  What happens if you don’t use the right stabilizer?  Your embroidery will not look ok.  Again, if for some strange reason you are OK with just OK, then keep using water soluble stabilizers for the back of towels…or forget using stabilizers and have none.  Yes, your embroidery *may*look ok when you are done, and it may be ok, but it sure isn’t great.  A lot of people can take their OK embroidery off their machine and gift it or give it to a customer or a friend.  Hooah, you did your first or 100thembroidery.  What is going to happen when they wash it?  If you have no stabilizer, there is nothing to keep the stitches from moving around or clumping up and looking terrible.  People don’t think of this part when they are done with their embroidery.  Embroidery is meant to last through washings and regular use – but only if you stabilize it properly.  Otherwise, the first time they wash your work, they will never use it again, and they will never come back to you again.  Seriously.  That is how it works.

If you take a tea-towel and do one design with a WSS (water soluble stabilizer) and one with a cut away stabilizer, stitch them out and look at them.  OK, the cutaway is going to look sharper, be in registration and look GREAT.  The other one is probably OK.  Now wash them both.  Now, look at them side by side.  If you don’t believe me, try it for yourself.  The properly hooped and stabilized embroidery will still look great, and the other one, well, not so much.  I have seen people actually state that they will NOT use stabilizer on the back of anything because it doesn’t look nice with the stabilizer showing.  Well, that may be the case, but that is how it is done!  If you tidy up the stabilizer, it doesn’t look bad at all, but put your focus on the FRONT where the embroidery is – and when you ask your friend 6 months later “how is the personalized towel I made for you” the answer will be “it is still beautiful” if you use the right stabilizer for the job.  After all, you do embroidery so it will last right? You do embroidery for kids so they can enjoy it, right?  You do embroidery for customers so that they will keep coming back, right?  If you do embroidery that only lasts through a wash or two, do you really think they will be coming back?  No.  No, they wont.  I have a shirt that I embroidered about 10 years ago (it’s my favorite shirt) and I have washed it literally hundreds of times.  And it still looks great and I still get compliments on it.  Don’t you want that effect on your customers and friends?

My advice:  Learn hooping skills and stop taking short cuts.  You are only hurting yourself when you decide that hooping is too difficult to learn, so why bother?  This works fine.  The key word being FINE.  I don’t want just fine, I want long lasting beautiful embroidery that I can be proud of.  Oh, I know some of you are saying, “well, none of my customers/friends/kids have complained about it”  and that might be correct, however, they may not complain, but they will go elsewhere. Guaranteed.

Here is a quick video that shows you some of the basic hooping skills.  Even if you have been doing embroidery for a while, this video is going to give you a few pointers on how to hoop properly.  Learn it, and learn it well.  Once you start hooping correctly, your embroidery will change and look better.

Next week’s blog, we are going to talk about placement.  Once you get basic hooping done properly, we have to put that together with placement and how to hoop properly the first time so that your embroidery design is centered and is in the exact place that you want it, on any fabric.

Until next time, hoop properly and Happy Stitching!

Sue Brown

OML Embroidery

DON’T FORGET TO SUBSCRIBE TO THE OML EMBROIDERY YOUTUBE CHANNEL and LIKE and SHARE videos!!!

HOOP BURN….ewwwww

Hoop Burn (ewww)

Have you ever embroidered a beautiful design that stitched out perfectly and looks great – and then you unhoop it and see LINES where your hoop was? Ewwww, that’s hoop burn. Instead of doing the whole design again and making the hoop screws a bit on the loose side, you can hoop properly AND fix the hoop burn once and for all. And just for future reference, you need to hoop most fabric tightly in the hoop, or your embroidery will suffer – you might get shifting, puckering or other unsightly mistakes if you have not hooped properly. As I said in my last blog “your embroidery is only as good as your hooping skills” and that applies here too.

So how do you hoop without hoop burn? If you hoop properly you will probably get hoop burn on some fabrics. Stop trying to avoid hoop burn (and get bad embroidery) and accept the hoop burn, but fix it afterward!

What exactly is Hoop Burn? it is a nasty looking “ring” around your embroidery (no, nothing like ring around the collar, don’t worry) that makes embroidery look terrible. Here is a perfect example on some robes that I was stitching for a client. The material is a waffle knit light cotton fabric, and I hooped it properly in a 4×4 hoop (oh, Ii know it is a bit small for the hoop, but it was bigger than my smallest hoop, so I had to compromise there) With this kind of fabric, it is a bit stretchy, so you have to be careful hooping. I left a few extra marks on the fabric because I re-hooped more than once to get the position correct. (please note, it is better to re-hoop and start again rather than pulling the fabric in the hoop trying to fine tune your hooping. Please don’t pull on the fabric! if the fabric is even slightly stretchy, you will have ruined your embroidery by stretching the fabric before embroidering on the fabric – if you stretch it out in the hoop, embroider and then unhoop, the embroidery will be on stretched fabric and will not look nice – enter warped embroidery, puckering and a whole bunch of other issues).

how to fix hoop burnhow to fix hoop burn

Doesn’t that look terrible?? Yes. Yes, it does. And you certainly can’t give this back to a customer or give this to anyone, it looks terrible.

So stage 1, Hoop properly accept the hoop burn.
Stage 2, fix the hoop burn.

You may be very surprised to learn how to fix hoop burn. It is actually quick and easy, and it is used by professional embroidery studios worldwide. Ready for the answer?
STEAM.
That’s it. Instead of blowing off steam because you are frustrated, boil some water and have a cup of tea!

Let’s look at what is happening when you are hooping. You are taking the item (fabric) plus backing and compressing it into a hoop to hold it tight – and then making it tighter. What do you think happens to the fabric when you compress it tightly between two plastic pieces? It “burns” and leaves a mark. Of course, it is not actually burning, but it is compressing and dehydrating so to speak. It is similar to wrinkled clothes – you pop them into the dryer for a few minutes and the wrinkles are gone! In professional embroidery studios, they have a steamer machine – just a large machine that produces steam – the same ones that you use for wrinkled clothes. You can get the bigger version of this, or you can get a travel version. If you don’t want to spend any money, then have a cup of tea! Ok, well the tea part doesn’t matter, but the boiling water does! Pop on a kettle or even a pot of water and wait for it to boil. Once you have a good amount of steam carefully hold your item over the steam and your hoop marks will disappear! Remember, I said carefully – you don’t want to burn yourself or ruin your garment – you don’t need to saturate the fabric, just steam it a little bit. I suggest passing the fabric over the steam once and checking your results- that way you are sure you are not over steaming. If the hoop mark is still there, then pass over the steam once more, and so on, letting the fabric cool before the next steaming.
The results are amazing – no more hoop burn and your garment or fabric is as good as new!

fixing hoop burn

See the difference? The embroidery looks perfect, and you can’t tell where the hoop was at all!

IN SUMMARY:
HOOP PROPERLY AND ACCEPT THE BURN
FIX THE BURN WITH STEAM (and have a cup of tea for a job well done, too!)
And you will have beautiful embroidery on just about any fabric!

Until next time, Happy Digitizing and please hoop properly!

Sue B

PS.  Want to know more?  subscribe to my youtube channel and learn all you can about embroidery!

%d bloggers like this: